“Glad to” hear that!
I already opened a ticket and was asked for serial debug logs, then for the boot environment listing. Haven’t heard back since then…
Serial debug log per https://doc.turris.cz/doc/cs/troubleshooting/serial_link :
root@turris:/# Stopping router Turris.
Jan 22 21:04:11 crelay[8220]: Exit crelay daemon
Jan 22 21:04:11 ucollect[12807]: Removing plugin Spoof
Jan 22 21:04:11 ucollect[12807]: Unloading plugin library
[92386.767251] reboot: Restarting system
U-Boot 2015.04-04654-gbcfb33e-dirty (Jun 26 2015 - 12:50:49)
CPU0: P2020E, Version: 2.1, (0x80ea0021)
Core: e500, Version: 5.1, (0x80211051)
Clock Configuration:
CPU0:1200 MHz, CPU1:1200 MHz,
CCB:600 MHz,
DDR:400 MHz (800 MT/s data rate) (Asynchronous), LBC:37.500 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
wdt status 00000005 reset
Watchdog enabled
Board: TURRIS CPLD: V4.1 PCBA: V4.0
Error, wrong i2c adapter 2 max 2 possible
in: 56
out: 0
io_config: 255
rom_loc: nor upper bank
SD/MMC : 4-bit Mode
eSPI : Enabled
I2C: Error, wrong i2c adapter 2 max 2 possible
ready
SPI: ready
DRAM: Error, wrong i2c adapter 2 max 2 possible
Detected UDIMM 9905594-009.A00LF
WARNING: Calling __hwconfig without a buffer and before environment is ready
WARNING: Calling __hwconfig without a buffer and before environment is ready
2 GiB (DDR3, 64-bit, CL=6, ECC off)
Flash: 16 MiB
L2: 512 KiB enabled
NAND: 256 MiB
MMC: FSL_SDHC: 0
PCIe1: Root Complex of mini PCIe SLOT, no link, regs @ 0xffe0a000
PCIe1: Bus 00 - 00
PCIe2: Root Complex of PCIe SLOT, x1 gen1, regs @ 0xffe09000
02:00.0 - 168c:0030 - Network controller
PCIe2: Bus 01 - 02
PCIe3: Root Complex of PCIe SLOT, x1 gen1, regs @ 0xffe08000
04:00.0 - 104c:8241 - Serial bus controller
PCIe3: Bus 03 - 04
Error, wrong i2c adapter 2 max 2 possible
In: serial
Out: serial
Err: serial
Net: Phy 5 not found
PHY reset timed out
eTSEC1, eTSEC2, eTSEC3 [PRIME]
Error: eTSEC3 address not set.
Hit any key to stop autoboot: 1 0
BOOT NAND
reading zImage
3299361 bytes read in 154 ms (20.4 MiB/s)
wdt status 00000003
reading fdt
12945 bytes read in 14 ms (902.3 KiB/s)
## Booting kernel from Legacy Image at 02100000 ...
Image Name: Linux-4.4.169-49a62e79231da4ac50
Created: 2019-01-15 8:50:53 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 3299297 Bytes = 3.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 02000000
Booting using the fdt blob at 0x2000000
Uncompressing Kernel Image ... OK
Loading Device Tree to 03ff9000, end 03fff290 ... OK
WARNING: could not find compatible node fsl-usb2-dr
[ 0.000000] Using P2020 RDB machine description
[ 0.000000] Memory CAM mapping: 256 Mb, residual: 0Mb
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.169-49a62e79231da4ac50e66e6eb4cd7945-2 (beast@build) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r47055) ) #1 SMP Tue Jan 15 09:50:48 CET 2019
[ 0.000000] CPU maps initialized for 1 thread per core
[ 0.000000] bootconsole [udbg0] enabled
setup_arch: initmem
mpc85xx_rdb_setup_arch()
[ 0.000000] mpc85xx_qe_init: Could not find Quicc Engine node
[ 0.000000] MPC85xx RDB board from Freescale Semiconductor
arch: exit
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Normal empty
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[ 0.000000] PERCPU: Embedded 10 pages/cpu @cfd89000 s9420 r8192 d23348 u40960
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: root=/dev/mmcblk0p2 rootwait rw rootfstype=btrfs rootflags=subvol=@,commit=5 console=ttyS0,115200
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 186720K/262144K available (5008K kernel code, 176K rwdata, 1092K rodata, 196K init, 259K bss, 75424K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffbf000..0xfffff000 : fixmap
[ 0.000000] * 0xffc00000..0xffe00000 : highmem PTEs
[ 0.000000] * 0xffbfd000..0xffc00000 : early ioremap
[ 0.000000] * 0xd1000000..0xffbfd000 : vmalloc & ioremap
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs
[ 0.000000] mpic: ISU size: 256, shift: 8, mask: ff
[ 0.000000] mpic: Initializing for 256 sources
[ 0.000000] mpc85xx_rdb_pic_init: Could not find qe-ic node
[ 0.000008] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0x114c1bade8, max_idle_ns: 440795203839 ns
[ 0.010275] clocksource: timebase mult[d555555] shift[24] registered
[ 0.016656] pid_max: default: 32768 minimum: 301
[ 0.021301] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.027842] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.035251] Initializing cgroup subsys io
[ 0.039189] Initializing cgroup subsys memory
[ 0.043542] Initializing cgroup subsys devices
[ 0.047963] Initializing cgroup subsys freezer
[ 0.052395] Initializing cgroup subsys net_cls
[ 0.056828] Initializing cgroup subsys pids
[ 0.061147] mpic: requesting IPIs...
[ 0.065643] Brought up 2 CPUs
[ 0.070647] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.080324] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.086505] xor: measuring software checksum speed
[ 0.101263] 8regs : 1472.000 MB/sec
[ 0.115400] 8regs_prefetch: 1312.000 MB/sec
[ 0.129884] 32regs : 1472.000 MB/sec
[ 0.144018] 32regs_prefetch: 1360.000 MB/sec
[ 0.148550] xor: using function: 32regs (1472.000 MB/sec)
[ 0.154263] NET: Registered protocol family 16
[ 0.163678] cpuidle: using governor ladder
[ 0.173927] Found FSL PCI host bridge at 0x00000000ffe08000. Firmware bus number: 0->1
[ 0.181775] PCI host bridge /pcie@ffe08000 (primary) ranges:
[ 0.187424] MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000
[ 0.194637] IO 0x00000000ffc20000..0x00000000ffc2ffff -> 0x0000000000000000
[ 0.201775] /pcie@ffe08000: PCICSRBAR @ 0xfff00000
[ 0.206545] setup_pci_atmu: end of DRAM 10000000
[ 0.211428] Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->1
[ 0.219270] PCI host bridge /pcie@ffe09000 ranges:
[ 0.224137] MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000
[ 0.231351] IO 0x00000000ffc10000..0x00000000ffc1ffff -> 0x0000000000000000
[ 0.238487] /pcie@ffe09000: PCICSRBAR @ 0xfff00000
[ 0.243260] setup_pci_atmu: end of DRAM 10000000
[ 0.248117] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0
[ 0.255957] PCI host bridge /pcie@ffe0a000 ranges:
[ 0.260825] MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000
[ 0.268038] IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000
[ 0.275175] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000
[ 0.279947] setup_pci_atmu: end of DRAM 10000000
[ 0.293543] PCI: Probing PCI hardware
[ 0.297275] fsl-pci ffe08000.pcie: PCI host bridge to bus 0000:00
[ 0.303296] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.309461] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xdfffffff]
[ 0.316330] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.323836] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.329205] fsl-pci ffe09000.pcie: PCI host bridge to bus 0001:02
[ 0.335226] pci_bus 0001:02: root bus resource [io 0x20000-0x2ffff] (bus address [0x0000-0xffff])
[ 0.344173] pci_bus 0001:02: root bus resource [mem 0xa0000000-0xbfffffff]
[ 0.351041] pci_bus 0001:02: root bus resource [bus 02-ff]
[ 0.356767] pci 0001:02:00.0: Primary bus is hard wired to 0
[ 0.362349] pci 0001:02:00.0: bridge configuration invalid ([bus 01-01]), reconfiguring
[ 0.373371] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
[ 0.378728] fsl-pci ffe0a000.pcie: PCI host bridge to bus 0002:04
[ 0.384749] pci_bus 0002:04: root bus resource [io 0x40000-0x4ffff] (bus address [0x0000-0xffff])
[ 0.393696] pci_bus 0002:04: root bus resource [mem 0x80000000-0x9fffffff]
[ 0.400564] pci_bus 0002:04: root bus resource [bus 04-ff]
[ 0.406279] pci 0002:04:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.414298] pci 0002:04:00.0: PCI bridge to [bus 05-ff]
[ 0.419532] PCI: Cannot allocate resource region 0 of PCI bridge 1, will remap
[ 0.426686] PCI: Cannot allocate resource region 0 of device 0000:00:00.0, will remap
[ 0.434502] PCI: Cannot allocate resource region 0 of device 0001:02:00.0, will remap
[ 0.442326] PCI: Cannot allocate resource region 0 of device 0002:04:00.0, will remap
[ 0.450183] pci 0000:00:00.0: BAR 0: no space for [mem size 0x00100000]
[ 0.456755] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x00100000]
[ 0.463710] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.468665] pci 0000:00:00.0: bridge window [mem 0xc0000000-0xdfffffff]
[ 0.475445] pci_bus 0000:00: Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.484516] pci 0001:02:00.0: BAR 0: no space for [mem size 0x00100000]
[ 0.491093] pci 0001:02:00.0: BAR 0: failed to assign [mem size 0x00100000]
[ 0.498051] pci 0001:03:00.0: BAR 6: assigned [mem 0xa0020000-0xa002ffff pref]
[ 0.505267] pci 0001:02:00.0: PCI bridge to [bus 03]
[ 0.510218] pci 0001:02:00.0: bridge window [io 0x20000-0x2ffff]
[ 0.516477] pci 0001:02:00.0: bridge window [mem 0xa0000000-0xbfffffff]
[ 0.523258] pci_bus 0001:02: Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.532336] pci 0002:04:00.0: BAR 0: no space for [mem size 0x00100000]
[ 0.538906] pci 0002:04:00.0: BAR 0: failed to assign [mem size 0x00100000]
[ 0.545860] pci 0002:04:00.0: PCI bridge to [bus 05]
[ 0.550816] pci 0002:04:00.0: bridge window [io 0x40000-0x4ffff]
[ 0.557075] pci 0002:04:00.0: bridge window [mem 0x80000000-0x9fffffff]
[ 0.563856] pci_bus 0002:04: Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.573188] mpic-msgr ffe41400.message: Found 0 message registers
[ 0.579204] mpic-msgr ffe41400.message: Of-device full name /soc@ffe00000/message@41400
[ 0.587208] mpic-msgr ffe41400.message: Failed to find message register block alias
[ 0.618608] raid6: int32x1 gen() 171 MB/s
[ 0.639920] raid6: int32x1 xor() 218 MB/s
[ 0.661281] raid6: int32x2 gen() 300 MB/s
[ 0.682598] raid6: int32x2 xor() 263 MB/s
[ 0.703940] raid6: int32x4 gen() 398 MB/s
[ 0.725257] raid6: int32x4 xor() 289 MB/s
[ 0.746617] raid6: int32x8 gen() 378 MB/s
[ 0.767926] raid6: int32x8 xor() 253 MB/s
[ 0.772110] raid6: using algorithm int32x4 gen() 398 MB/s
[ 0.777499] raid6: .... xor() 289 MB/s, rmw enabled
[ 0.782367] raid6: using intx1 recovery algorithm
[ 0.788341] clocksource: Switched to clocksource timebase
[ 0.794462] NET: Registered protocol family 2
[ 0.799120] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.806029] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.812460] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.818825] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.824626] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.830988] NET: Registered protocol family 1
[ 0.841454] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.847377] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (LZO) (LZMA) (RTIME) (RUBIN) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.860063] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.867396] io scheduler noop registered
[ 0.871297] io scheduler deadline registered (default)
[ 0.876713] pcieport 0001:02:00.0: enabling device (0106 -> 0107)
[ 0.882888] pcieport 0002:04:00.0: enabling device (0106 -> 0107)
[ 0.889221] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt
[ 0.896113] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[ 0.902661] pcieport 0001:02:00.0: Signaling PME through PCIe PME interrupt
[ 0.909581] pci 0001:03:00.0: Signaling PME through PCIe PME interrupt
[ 0.916126] pcieport 0002:04:00.0: Signaling PME through PCIe PME interrupt
[ 0.949094] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.957597] console [ttyS0] disabled
[ 0.961140] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42, base_baud = 37500000) is a 16550A
[ 0.969813] console [ttyS0] enabled
[ 0.969813] console [ttyS0] enabled
[ 0.976748] bootconsole [udbg0] disabled
[ 0.976748] bootconsole [udbg0] disabled
[ 0.985000] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 37500000) is a 16550A
[ 0.994293] console [ttyS0] disabled
[ 0.997910] console [ttyS0] enabled
[ 1.001805] ffe04600.serial: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 37500000) is a 16550
[ 1.017633] brd: module loaded
[ 1.021410] ef000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101
[ 1.031432] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.036600] Amd/Fujitsu Extended Query version 1.3.
[ 1.041656] number of CFI chips: 1
[ 1.045280] 6 ofpart partitions found on MTD device ef000000.nor
[ 1.051341] Creating 6 MTD partitions on "ef000000.nor":
[ 1.056664] 0x000000000000-0x000000020000 : "NOR (RO) DTB Image"
[ 1.063285] 0x000000020000-0x0000001c0000 : "NOR (RO) Linux Kernel Image"
[ 1.070621] 0x0000001c0000-0x000000340000 : "NOR (RO) JFFS2 Root File System"
[ 1.078328] 0x000000340000-0x000000e40000 : "NOR (RO) NAND FW backup"
[ 1.085339] 0x000000e40000-0x000000f00000 : "NOR (RW) Cert backup"
[ 1.092086] 0x000000f00000-0x000001000000 : "NOR (RO) U-Boot Image"
[ 1.099465] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.105853] nand: Micron MT29F2G08ABAEAWP
[ 1.109867] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.118778] Bad block table found at page 131008, version 0x01
[ 1.125380] Bad block table found at page 130944, version 0x01
[ 1.131810] 4 ofpart partitions found on MTD device ff800000.flash
[ 1.138005] Creating 4 MTD partitions on "ff800000.flash":
[ 1.143497] 0x000000000000-0x000000200000 : "NAND (RW) DTB Image"
[ 1.150187] 0x000000200000-0x000000700000 : "NAND (RW) Linux Kernel Image"
[ 1.157604] 0x000000700000-0x000010000000 : "NAND (RW) JFFS2 Root File System"
[ 1.165587] 0x000000000000-0x000010000000 : "rootfs-ubifs"
[ 1.171823] eLBC NAND device at 0xff800000, bank 1
[ 1.177090] fsl_espi ffe07000.spi: cs=0, init_csmode=0x100008
[ 1.182857] fsl_espi ffe07000.spi: cs=1, init_csmode=0x100008
[ 1.188619] fsl_espi ffe07000.spi: cs=2, init_csmode=0x100008
[ 1.194372] fsl_espi ffe07000.spi: cs=3, init_csmode=0x100008
[ 1.201187] fsl_espi ffe07000.spi: at 0xd11d2000 (irq = 59)
[ 1.207222] libphy: Fixed MDIO Bus: probed
[ 1.211526] libphy: Freescale PowerQUICC MII Bus: probed
[ 1.219363] switch0: Atheros AR8337 rev. 2 switch registered on mdio@ffe24520
[ 1.271038] fsl-gianfar ffe24000.ethernet: enabled errata workarounds, flags: 0x4
[ 1.288959] fsl-gianfar ffe24000.ethernet eth0: mac: 00:00:11:22:33:44
[ 1.295500] fsl-gianfar ffe24000.ethernet eth0: Running with NAPI enabled
[ 1.302297] fsl-gianfar ffe24000.ethernet eth0: RX BD ring size for Q[0]: 256
[ 1.309440] fsl-gianfar ffe24000.ethernet eth0: TX BD ring size for Q[0]: 256
[ 1.316872] fsl-gianfar ffe25000.ethernet: enabled errata workarounds, flags: 0x4
[ 1.334740] fsl-gianfar ffe25000.ethernet eth1: mac: 00:00:11:22:33:45
[ 1.341282] fsl-gianfar ffe25000.ethernet eth1: Running with NAPI enabled
[ 1.348078] fsl-gianfar ffe25000.ethernet eth1: RX BD ring size for Q[0]: 256
[ 1.355221] fsl-gianfar ffe25000.ethernet eth1: TX BD ring size for Q[0]: 256
[ 1.362441] fsl-gianfar ffe26000.ethernet: enabled errata workarounds, flags: 0x4
[ 1.380303] fsl-gianfar ffe26000.ethernet eth2: mac: 00:00:00:00:00:00
[ 1.386847] fsl-gianfar ffe26000.ethernet eth2: Running with NAPI enabled
[ 1.393643] fsl-gianfar ffe26000.ethernet eth2: RX BD ring size for Q[0]: 256
[ 1.400786] fsl-gianfar ffe26000.ethernet eth2: TX BD ring size for Q[0]: 256
[ 1.408033] ucc_geth_driver: QE UCC Gigabit Ethernet Controller
[ 1.414163] i2c /dev entries driver
[ 1.417795] mpc-i2c ffe03000.i2c: timeout 1000000 us
[ 1.425271] rtc-ds1307 0-006f: rtc core: registered mcp7940x as rtc0
[ 1.431650] rtc-ds1307 0-006f: 64 bytes nvram
[ 1.436197] mpc-i2c ffe03100.i2c: timeout 1000000 us
[ 1.441445] booke_wdt: powerpc book-e watchdog driver loaded
[ 1.447296] sdhci: Secure Digital Host Controller Interface driver
[ 1.453486] sdhci: Copyright(c) Pierre Ossman
[ 1.457851] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.463657] /soc@ffe00000/sdhc@2e000: voltage-ranges unspecified
[ 1.469683] sdhci-esdhc ffe2e000.sdhc: No vmmc regulator found
[ 1.475522] sdhci-esdhc ffe2e000.sdhc: No vqmmc regulator found
[ 1.503856] mmc0: SDHCI controller on ffe2e000.sdhc [ffe2e000.sdhc] using DMA
[ 1.511719] NET: Registered protocol family 10
[ 1.516791] NET: Registered protocol family 17
[ 1.521297] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.533952] Bridge firewalling registered
[ 1.537980] 8021q: 802.1Q VLAN Support v1.8
[ 1.543004] BTRFS: using crc32c-generic for crc32c
[ 1.549140] Btrfs loaded, integrity-checker=on
[ 1.555103] rtc-ds1307 0-006f: setting system clock to 2019-01-22 20:04:20 UTC (1548187460)
[ 1.564038] Waiting for root device /dev/mmcblk0p2...
[ 1.578972] mmc0: new high speed SDHC card at address 0007
[ 1.584824] mmcblk0: mmc0:0007 SD16G 14.5 GiB
[ 1.590451] mmcblk0: p1 p2
[ 1.671653] BTRFS: device fsid 3e7862ed-c9b6-4fc6-a9b7-b830c06cf399 devid 1 transid 4434 /dev/root
[ 1.683964] BTRFS info (device mmcblk0p2): disk space caching is enabled
[ 1.690686] BTRFS: has skinny extents
[ 1.713452] BTRFS: detected SSD devices, enabling SSD mode
[ 1.733881] VFS: Mounted root (btrfs filesystem) on device 0:13.
[ 1.740137] Freeing unused kernel memory: 196K
[ 1.876060] init: Console is alive
[ 1.879583] init: - watchdog -
[ 2.888602] usbcore: registered new interface driver usbfs
[ 2.894154] usbcore: registered new interface driver hub
[ 2.899526] usbcore: registered new device driver usb
[ 2.906333] Button Hotplug driver version 0.4.1
[ 2.912928] exFAT: Version 1.2.9
[ 2.942918] JFS: nTxBlock = 1975, nTxLock = 15804
[ 2.971248] SGI XFS with security attributes, no debug enabled
[ 2.982790] SCSI subsystem initialized
[ 2.988370] usbcore: registered new interface driver usb-storage
[ 2.995128] usbcore: registered new interface driver uas
[ 3.003600] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.010563] ehci-platform: EHCI generic platform driver
[ 3.016358] ehci-fsl: Freescale EHCI Host controller driver
[ 3.022005] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 3.028648] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 3.035946] fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000
[ 3.046860] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 3.052894] hub 1-0:1.0: USB hub found
[ 3.056678] hub 1-0:1.0: 1 port detected
[ 3.069995] uhci_hcd: USB Universal Host Controller Interface driver
[ 3.079721] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 3.084987] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[ 3.092558] xhci_hcd 0000:01:00.0: hcc params 0x0270f06d hci version 0x96 quirks 0x00000000
[ 3.101491] hub 2-0:1.0: USB hub found
[ 3.105290] hub 2-0:1.0: 4 ports detected
[ 3.109696] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 3.114946] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3
[ 3.122429] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.130927] hub 3-0:1.0: USB hub found
[ 3.134715] hub 3-0:1.0: 4 ports detected
[ 3.361857] usb 1-1: new high-speed USB device number 2 using fsl-ehci
[ 3.482547] hub 1-1:1.0: USB hub found
[ 3.486441] hub 1-1:1.0: 2 ports detected
[ 3.883150] init: - preinit -
ifconfig: SIOCSIFFLAGS: Cannot assign requested address
sendto(): Network is unre[ 4.559263] random: mktemp: uninitialized urandom read (6 bytes read, 79 bits of entropy available)
achable
[ 4.570323] random: mktemp: uninitialized urandom read (6 bytes read, 79 bits of entropy available)
[ 4.581223] random: mktemp: uninitialized urandom read (6 bytes read, 79 bits of entropy available)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.492967] usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 5.514247] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 5.520899] random: procd: uninitialized urandom read (4 bytes read, 82 bits of entropy available)
[ 5.522951] scsi host0: usb-storage 3-1:1.0
[ 6.528649] scsi 0:0:0:0: Direct-Access ST380011 A PQ: 0 ANSI: 7
[ 6.537797] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 6.546943] sd 0:0:0:0: [sda] Write Protect is off
[ 6.553185] sd 0:0:0:0: [sda] No Caching mode page found
[ 6.558511] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 6.587686] sda: sda1 sda2 sda3 sda4
[ 6.595318] sd 0:0:0:0: [sda] Attached SCSI disk
[ 8.279393] mount_root: mounting /dev/root
[ 12.130489] BTRFS info (device mmcblk0p2): disk space caching is enabled
[ 12.137400] mount_root: loading kmods from internal overlay
[ 12.561504] random: nonblocking pool is initialized
[ 12.616631] block: attempting to load /etc/config/fstab
[ 12.625739] block: extroot: not configured
ifconfig: SIOCSIFFLAGS: Cannot ass[ 12.637181] procd: - early -
ign r[ 12.640473] procd: - watchdog -
equested address
Failed to connect to ubus
Failed to connect to ubus
[ 13.287299] procd: - ubus -
[ 14.293289] procd: - init -
Please press Enter to activate this console.
[ 14.410113] NET: Registered protocol family 38
[ 14.425330] Netfilter messages via NETLINK v0.30.
[ 14.438789] md: linear personality registered for level -1
[ 14.444977] md: raid0 personality registered for level 0
[ 14.451566] md: raid1 personality registered for level 1
[ 14.458349] md: raid10 personality registered for level 10
[ 14.468552] md: raid6 personality registered for level 6
[ 14.473964] md: raid5 personality registered for level 5
[ 14.479295] md: raid4 personality registered for level 4
[ 14.488448] FS-Cache: Loaded
[ 14.492212] md: multipath personality registered for level -4
[ 14.500200] NET: Registered protocol family 8
[ 14.504583] NET: Registered protocol family 20
[ 14.514647] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[ 14.529231] Key type dns_resolver registered
[ 14.538311] NET: Registered protocol family 33
[ 14.542785] Key type rxrpc registered
[ 14.546450] Key type rxrpc_s registered
[ 14.554702] kAFS: Red Hat AFS client v0.1 registering.
[ 14.559926] FS-Cache: Netfs 'afs' registered for caching
[ 14.601110] RPC: Registered named UNIX socket transport module.
[ 14.607075] RPC: Registered udp transport module.
[ 14.611814] RPC: Registered tcp transport module.
[ 14.616595] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 14.646440] NFS: Registering the id_resolver key type
[ 14.651540] Key type id_resolver registered
[ 14.655749] Key type id_legacy registered
[ 14.660776] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 14.671265] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 14.680944] RxRPC: Registered security type 2 'rxkad'
[ 14.705260] tun: Universal TUN/TAP device driver, 1.6
[ 14.710363] tun: (C) 1999-2004 Max Krasnyansky
[ 14.722387] sit: IPv6 over IPv4 tunneling driver
[ 14.729957] gre: GRE over IPv4 demultiplexor driver
[ 14.735641] ip_gre: GRE over IPv4 tunneling driver
[ 14.752592] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 14.762230] PPP generic driver version 2.4.2
[ 14.768938] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.785396] nf_conntrack version 0.5.0 (3951 buckets, 15804 max)
[ 14.910593] ip_set: protocol 6
[ 15.423886] cryptodev: driver 1.8 loaded.
[ 15.465334] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 15.473372] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 15.639070] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 15.853477] u32 classifier
[ 15.856202] input device check on
[ 15.859876] Actions configured
[ 15.923416] Mirror/redirect action on
[ 16.047383] GACT probability on
[ 16.539439] netem: version 1.3
[ 16.741256] fuse init (API version 7.23)
[ 16.796661] usbcore: registered new interface driver cdc_acm
[ 16.802338] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 16.812259] usbcore: registered new interface driver cdc_wdm
[ 16.823427] Ebtables v2.0 registered
[ 16.832085] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.858241] ctnetlink v0.93: registering with nfnetlink.
[ 16.906355] nfnl_acct: registering with nfnetlink.
[ 16.913340] PPP MPPE Compression module registered
[ 16.919475] NET: Registered protocol family 24
[ 16.927014] usbcore: registered new interface driver ums-alauda
[ 16.935028] usbcore: registered new interface driver ums-cypress
[ 16.943470] usbcore: registered new interface driver ums-datafab
[ 16.951423] usbcore: registered new interface driver ums-freecom
[ 16.959762] usbcore: registered new interface driver ums-isd200
[ 16.967980] usbcore: registered new interface driver ums-jumpshot
[ 16.976281] usbcore: registered new interface driver ums-karma
[ 16.984937] usbcore: registered new interface driver ums-sddr09
[ 16.993291] usbcore: registered new interface driver ums-sddr55
[ 17.001627] usbcore: registered new interface driver ums-usbat
[ 17.020195] usbcore: registered new interface driver usbserial
[ 17.026156] usbcore: registered new interface driver usbserial_generic
[ 17.032760] usbserial: USB Serial support registered for generic
[ 17.061590] xt_time: kernel timezone is -0000
[ 17.071959] usbcore: registered new interface driver cdc_ether
[ 17.081102] usbcore: registered new interface driver ftdi_sio
[ 17.086949] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 17.111026] usbcore: registered new interface driver qmi_wwan
[ 17.119390] usbcore: registered new interface driver rndis_host
[ 17.264978] ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xd4000000, irq=37
[ 17.275060] usbcore: registered new interface driver option
[ 17.280758] usbserial: USB Serial support registered for GSM modem (1-port)
Jan 22 21:04:41 haveged: haveged starting up
Jan 22 21:04:41 haveged: haveged: ver: 1.9.4; arch: ppc; vend: ; build: (gcc 4.8.3 V); collect: 128K
Jan 22 21:04:41 haveged: haveged: cpu: (); data: 32K (P); inst: 32K (P); idx: 15/40; sz: 30904/80288
Jan 22 21:04:41 haveged: haveged: fills: 0, generated: 0
Jan 22 21:04:57 ucollect[7363]: Initializing emergency signal handlers
Jan 22 21:04:57 ucollect[7363]: Creating a main loop
Jan 22 21:04:57 ucollect[7363]: Creating uplink
Jan 22 21:04:57 ucollect[7363]: Initializing PCAP (in) on lo
Jan 22 21:04:57 ucollect[7363]: Initializing PCAP (out) on lo
Jan 22 21:04:57 ucollect[7363]: Loading plugin library libplugin_ucollect_badconf_25.so
Jan 22 21:04:57 ucollect[7363]: Installing plugin Badconf with api version 0
Jan 22 21:04:57 ucollect[7363]: Loading plugin library libplugin_ucollect_bandwidth_22.so
Jan 22 21:04:57 ucollect[7363]: Installing plugin Bandwidth with api version 0
Jan 22 21:04:57 ucollect[7363]: Loading plugin library libplugin_ucollect_count_28.so
Jan 22 21:04:57 ucollect[7363]: Installing plugin Count with api version 0
Jan 22 21:04:57 ucollect[7363]: Loading plugin library libplugin_ucollect_fake_23.so
Jan 22 21:04:57 ucollect[7363]: Installing plugin Fake with api version 0
Jan 22 21:04:57 ucollect[7363]: Loading plugin library libplugin_ucollect_flow_33.so
Jan 22 21:04:57 ucollect[7363]: Installing plugin Flow with api version 2
Jan 22 21:04:57 ucollect[7363]: Loading plugin library libpluglib_ucollect_diffstore_1.2.so
Jan 22 21:04:57 ucollect[7363]: Loading plugin library libplugin_ucollect_fwup_12.so
Jan 22 21:04:57 ucollect[7363]: Installing plugin Fwup with api version 2
Jan 22 21:04:57 ucollect[7363]: Loading plugin library libpluglib_ucollect_diffstore_1.2.so
Jan 22 21:04:57 ucollect[7363]: Loading plugin library libplugin_ucollect_refused_13.so
Jan 22 21:04:57 ucollect[7363]: Installing plugin Refused with api version 0
Jan 22 21:04:57 ucollect[7363]: Loading plugin library libplugin_ucollect_sniff_19.so
Jan 22 21:04:57 ucollect[7363]: Installing plugin Sniff with api version 0
Jan 22 21:04:57 ucollect[7363]: Loading plugin library libplugin_ucollect_spoof_8.so
Jan 22 21:04:57 ucollect[7363]: Installing plugin Spoof with api version 0
Jan 22 21:04:57 ucollect[7363]: Changing remote uplink address to api.turris.cz:5679
Jan 22 21:04:57 ucollect[7363]: Failed to resolve uplink api.turris.cz:5679: Name or service not known
Jan 22 21:04:57 ucollect[7363]: Didn't get any V4 address in resolution of api.turris.cz
Jan 22 21:04:57 ucollect[7363]: Didn't get any V6 address in resolution of api.turris.cz
Jan 22 21:04:57 ucollect[7363]: Sending login credentials disabled
Jan 22 21:04:57 ucollect[7363]: Sending login credentials disabled
Jan 22 21:04:57 ucollect[7363]: Sending login credentials disabled
Jan 22 21:04:57 ucollect[7363]: Sending login credentials disabled
Jan 22 21:04:57 ucollect[7363]: Sending login credentials disabled
Jan 22 21:04:57 ucollect[7363]: Sending login credentials disabled
Jan 22 21:04:57 ucollect[7363]: Unloading plugin library
Jan 22 21:04:57 ucollect[7363]: Running the main loop
Jan 22 21:04:57 ucollect[7363]: Reconnecting to api.turris.cz:5679 now
Jan 22 21:04:57 ucollect[7363]: Socat started
Jan 22 21:04:57 ucollect[7363]: Failed to resolve uplink api.turris.cz:5679: Name or service not known
Jan 22 21:04:57 ucollect[7363]: Didn't get any V4 address in resolution of api.turris.cz
Jan 22 21:04:57 ucollect[7363]: Didn't get any V6 address in resolution of api.turris.cz
Jan 22 21:04:57 ucollect[7363]: Error from socat: 2019/01/22 21:04:57 socat[7399] E getaddrinfo("api.turris.cz", "NULL", {1,10,1,6}, {}): Name or service not known
Jan 22 21:04:57 ucollect[7363]: Remote closed the uplink api.turris.cz:5679, reconnecting
Jan 22 21:04:57 ucollect[7363]: epoll_wait on 3 interrupted, retry
Jan 22 21:04:57 ucollect[7363]: Reconnecting to api.turris.cz:5679 now
Jan 22 21:04:57 ucollect[7363]: Reconnecting too often, waiting a little while
Jan 22 21:04:57 ucollect[7363]: Going to reconnect to api.turris.cz:5679 after 2 seconds
Jan 22 21:04:59 ucollect[7363]: Reconnecting to api.turris.cz:5679 now
Jan 22 21:04:59 ucollect[7363]: Socat started
Jan 22 21:04:59 ucollect[7363]: Failed to resolve uplink api.turris.cz:5679: Name or service not known
Jan 22 21:04:59 ucollect[7363]: Didn't get any V4 address in resolution of api.turris.cz
Jan 22 21:04:59 ucollect[7363]: Didn't get any V6 address in resolution of api.turris.cz
Jan 22 21:04:59 ucollect[7363]: Error from socat: 2019/01/22 21:04:59 socat[7811] E getaddrinfo("api.turris.cz", "NULL", {1,2,1,6}, {}): Name or service not known
Jan 22 21:04:59 ucollect[7363]: Remote closed the uplink api.turris.cz:5679, reconnecting
Jan 22 21:04:59 ucollect[7363]: epoll_wait on 3 interrupted, retry
Jan 22 21:04:59 ucollect[7363]: Reconnecting to api.turris.cz:5679 now
Jan 22 21:04:59 ucollect[7363]: Reconnecting too often, waiting a little while
Jan 22 21:04:59 ucollect[7363]: Going to reconnect to api.turris.cz:5679 after 4 seconds
Jan 22 21:05:03 ucollect[7363]: Reconnecting to api.turris.cz:5679 now
Jan 22 21:05:03 ucollect[7363]: Socat started
Jan 22 21:05:03 ucollect[7363]: Failed to resolve uplink api.turris.cz:5679: Name or service not known
Jan 22 21:05:03 ucollect[7363]: Didn't get any V4 address in resolution of api.turris.cz
Jan 22 21:05:03 ucollect[7363]: Didn't get any V6 address in resolution of api.turris.cz
Jan 22 21:05:03 ucollect[7363]: Error from socat: 2019/01/22 21:05:03 socat[7950] E getaddrinfo("api.turris.cz", "NULL", {1,10,1,6}, {}): Name or service not known
Jan 22 21:05:03 ucollect[7363]: Remote closed the uplink api.turris.cz:5679, reconnecting
Jan 22 21:05:03 ucollect[7363]: epoll_wait on 3 interrupted, retry
Jan 22 21:05:03 ucollect[7363]: Reconnecting to api.turris.cz:5679 now
Jan 22 21:05:03 ucollect[7363]: Reconnecting too often, waiting a little while
Jan 22 21:05:03 ucollect[7363]: Going to reconnect to api.turris.cz:5679 after 8 seconds
Router Turris successfully started.
Boot environment variable - I had to stop booting via serial debug line and enter command printenv:
=> printenv
arch=sandbox
backbootcmd=setexpr.b reflash *0xFFA0001F;if test $reflash -ge $reflash_timeout; then echo BOOT NOR; run norboot; else echo BOOT NAND; run ubiboot; fi
baudrate=115200
board=sandbox
board_name=sandbox
boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr}
boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}extlinux/extlinux.conf
boot_net_pci_enum=pci enum
boot_net_usb_start=usb start
boot_prefixes=/ /boot/
boot_script_dhcp=boot.scr.uimg
boot_scripts=boot.scr.uimg boot.scr
boot_targets=host1 host0
bootargsmmc=root=/dev/mmcblk0p2 rootwait rw rootfstype=btrfs rootflags=subvol=@,commit=5 console=ttyS0,115200
bootargsnor=root=/dev/mtdblock2 rw rootfstype=jffs2 console=ttyS0,115200
bootargsubi=root=ubi0:rootfs rootfstype=ubifs ubi.mtd=9,2048 rootflags=chk_data_crc rw console=ttyS0,115200
bootcmd=setexpr.b reflash *0xFFA0001F;if test $reflash -ge $reflash_timeout; then echo BOOT NOR; run norboot; else echo BOOT NAND; mmc rescan; if fatload mmc 0:1 $nandbootaddr zImage; then run mmcboot; else run ubiboot; fi; fi
bootcmd_host0=setenv devnum 0; run host_boot
bootcmd_host1=setenv devnum 1; run host_boot
bootdelay=1
bootfile=uImage
bootm_size=0x10000000
consoledev=ttyS0
cpu=sandbox
distro_bootcmd=setenv scsi_need_init; for target in ${boot_targets}; do run bootcmd_${target}; done
eth1addr=00:00:11:22:33:45
eth3addr=00:00:11:22:33:46
eth5addr=00:00:11:22:33:47
ethact=eTSEC3
ethaddr=00:00:11:22:33:44
ethprime=eTSEC3
fdt_addr_r=0xc00000
fdtaddr=c00000
host_boot=if host dev ${devnum}; then setenv devtype host; run scan_dev_for_boot_part; fi
ide_boot=if ide dev ${devnum}; then setenv devtype ide; run scan_dev_for_boot_part; fi
ipaddr=1.2.3.4
jffs2nand=mtdblock9
jffs2nor=mtdblock3
kernel_addr_r=0x1000000
loadaddr=1000000
map_lowernorbank=i2c dev 1; i2c mw 18 1 02 1; i2c mw 18 3 fd 1
map_uppernorbank=i2c dev 1; i2c mw 18 1 00 1; i2c mw 18 3 fd 1
mmcboot=max6370_wdt_off; fatload mmc 0:1 $nandfdtaddr fdt; setenv bootargs $bootargsmmc; bootm $nandbootaddr - $nandfdtaddr
mtdids=nor0=ef000000.nor,nand0=nand
mtdparts=mtdparts=ef000000.nor:128k(dtb-image),1664k(kernel),1536k(root),11264k(backup),128k(cert),1024k(u-boot);nand:-(rootfs)
nandbootaddr=2100000
nandfdtaddr=2000000
netdev=eth0
nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr
norboot=max6370_wdt_off; env default -a; saveenv; setenv bootargs $bootargsnor; bootm 0xef020000 - 0xef000000
norbootaddr=ef080000
norfdtaddr=ef040000
pxefile_addr_r=0x2000
ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs ramdisk_size=$ramdisk_size;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr $ramdiskaddr $fdtaddr
ramdisk_addr_r=0x2000000
ramdisk_size=120000
ramdiskaddr=2000000
ramdiskfile=rootfs.ext2.gz.uboot
reflash_timeout=40
rootpath=/opt/nfsroot
sata_boot=if sata dev ${devnum}; then setenv devtype sata; run scan_dev_for_boot_part; fi
scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done;
scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done
scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}extlinux/extlinux.conf; then echo Found ${prefix}extlinux/extlinux.conf; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi
scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done
scriptaddr=0x1000
scsi_boot=run scsi_init; if scsi dev ${devnum}; then setenv devtype scsi; run scan_dev_for_boot_part; fi
scsi_init=if ${scsi_need_init}; then setenv scsi_need_init false; scsi scan; fi
stderr=serial
stdin=serial
stdout=serial
tftpflash=tftpboot $loadaddr $uboot; protect off 0xeff40000 +$filesize; erase 0xeff40000 +$filesize; cp.b $loadaddr 0xeff40000 $filesize; protect on 0xeff40000 +$filesize; cmp.b $loadaddr 0xeff40000 $filesize
ubiboot=max6370_wdt_off; setenv bootargs $bootargsubi; ubi part rootfs; ubifsmount ubi0:rootfs; ubifsload $nandfdtaddr /boot/fdt; ubifsload $nandbootaddr /boot/zImage; bootm $nandbootaddr - $nandfdtaddr
uboot=u-boot.bin
usb_boot=usb start; if usb dev ${devnum}; then setenv devtype usb; run scan_dev_for_boot_part; fi
Environment size: 4986/8188 bytes